Installation Guide

3. Tips for Installing on Windows

To compile and run Geant4 under Windows systems, some additional information and tools are required, although the installation produre is similar to that required on a UNIX based system. On Windows, the Cygwin toolset and the Microsoft Visual C++ compiler are used.
Cygwin32 is a UNIX development environment available for Microsoft Windows. You can freely obtain Cygwin32 from Cygwin or Cygwin/X.
We do not support direct use of Visual Studio; i.e. we do not provide Visual Studio workspace (.dsw) or project (.dsp) files, nor we do provide makefiles for the nmake application of MS Visual C++.

We use several of the tools provided by the Cygwin toolset:

• make.exe as a make tool
• g++.exe as a tool to analyse source file dependencies and create dependency (.d) files
• several other unix tools like cp, mv, rm, touch, etc.

The usage of Cygwin32 for the build environment results in a build procedure similar to that on a UNIX system. The documentation in the User's Guide for Application Developers, Section 10.5, is largely applicable in this case.

The following steps are required to install geant4:

1. Install Cygwin (see also notes above):
   We do not depend on any specific feature of the version of Cygwin, so newer versions (or slightly older) are expected to work.
2. Set the environment for MS Visual C++, i.e. set the paths to libraries, include files, and executables for MS Visual C++. This can be done by modifying the start-up batch file cygwin.bat of Cygwin32 to include all the MSDOS commands found in the file vcvars32.bat provided in MS Visual C++ (in the VC++ .NET compiler installation directory, and usually located inside the Common7/Tools directory). This modification should be done after the installation of the Cygwin toolset, so that the environment gets properly set at the time of the invocation of the shell.
3. Unpack the source code into a directory of your choice.
4. Start the Cygwin shell from the start menu.
5. At this point you're ready to install Geant4. If manual installation is chosen, you must set the necessary environment variables. There are various ways to do so; for example through a command file for the Cygwin bash shell. This command file could be named geant4-setup.sh, and you must execute it with
   

   	. geant4-setup.sh
       

   including the leading dot and blank space. You could also have this as your .bashrc file. The commands in the command file should be:

   	# Set G4SYSTEM 
   	export G4SYSTEM=WIN32-VC
   	#
   	# Set Path to CLHEP
   	export CLHEP_BASE_DIR=C:/usr/local
   	#
   	# --- Other optional settings
   	#Turn on verbose to show command used for compilation
   	#export CPPVERBOSE=1
   	#
       

   Note, in the example above, CLHEP was installed in C:/usr/local, therefore include/CLHEP and lib/CLHEP.lib must be included therein.
6. Once the environment is correctly set, the libraries are built using make from the geant4/source directory typing make from the Cygwin bash shell prompt.

The binary of the example is placed by default into the geant4/bin/WIN32-VC directory. You may run it either from this directory or from the examples/novice/N01 directory; sample input and output files are placed in each of the examples/novice directories. Some of the examples will need to read data files, and the place has to be given in environment variables again similar to the following example:

	#
	# Environment variables needed to find geant4 data files:
	#
	# Data for neutron scattering processes, 
	#    distributed in a separate tar file, then placed under data
	export NeutronHPCrossSections=c:/usr/local/geant4/data/G4NDL
	#
	# Nuclear Photon evaporation data,
	#    distributed with the source files under data 
	export G4LEVELGAMMADATA=c:/usr/local/geant4/data/PhotonEvaporation
	#
	# Data for radiative decay hadronic processes under data,
	#    distributed in a separate tar file
	export G4RADIOACTIVEDATA=c:/usr/local/geant4/data/RadiativeDecay
	#
	# Data for low energy electromagnetic processes,
	#    distributed in a separate tar file, then placed under data
	export G4LEDATA=c:/usr/local/geant4/data/G4EMLOW
	#

All compiler and linker options are set in config/sys/WIN32-VC.gmk. If you require options different from our choice, you can modify this file.

DLLs (Dynamic Link Libraries) on Windows are supported for .NET VC++ and can be built for the compound kernel libraries of Geant4 (see the Installation Procedure of this Guide for a dissertation on global/compound libraries).

The libraries can be built either manually, issuing the command:

        make dll

        export PATH=$PATH:/usr/local/geant4/lib/$G4SYSTEM